Menu Close

What is the default password for a Cisco router?

What is the default password for a Cisco router?

admin
Most routers and switches by Cisco have default passwords of admin or cisco, and default IP addresses of 192.168. 1.1 or 192.168. 1.254. However, some differ as shown in the table below..

How do I reset my Cisco 1721 router to factory settings?

Reset Router to Default Configuration

  1. With the router powered off, connect the power cord to your router, and plug the power cord into your power source.
  2. Find the Reset button on the router.
  3. Press and hold the Reset button while you power on the router.
  4. Release the Reset button after 10 seconds.

How do I find my Cisco router username and password?

When you access the device, you should be asked to enter a username and password. The default user name of your Cisco router is either “admin” or “cisco”. The default password of all Cisco routers is either “admin”, “cisco” or is a blank field.

How do I reset my Cisco 1800 router password?

Press Break on the terminal keyboard within 60 seconds of power up in order to put the router into ROMMON. If the break sequence does not work, refer to Standard Break Key Sequence Combinations During Password Recovery for other key combinations. Type confreg 0x2142 at the rommon 1> prompt in order to boot from Flash.

What is the default username and password?

#1) The default username and password can be obtained from the router manual which comes with the router when you first purchase and install it. #2) Generally, for most of the routers, the default username and password is “admin” and “admin”.

How do I find my Cisco WIFI password?

Windows 8: Find your password

  1. From the Start screen, swipe in from the right edge of the screen, and then tap Settings.
  2. Tap or click the wireless network icon .
  3. Tap and hold or right click on a wireless network name, and then choose View connection properties.
  4. Select Show characters to see the wireless network password.

What is the default router login?

Try a common username and password combination: By default, many routers use a blank username and the password “admin” (don’t type the quotes), the username “admin” and a blank password, or “admin” as both the username and password.

How do I reset my Cisco 1800 factory default?

How to Factory Reset 1800 series Cisco router

  1. Connect you PC to the router via console cable and connect using Putty.
  2. Boot the router while holding ctrl and break get into rommon1>
  3. Type the following command.
  4. Type Reset to start the factory reset.
  5. To enter config mode, issue the config terminal command.

What are the security requirements for the Cisco 1721 router?

This security policy describes how the 1721 and 1760 routers (Hardware Version: 1721, 1760; MOD1700-VPN: Hardware Version 2.1, Board Version A0; Firmware Version: IOS 12.3 (3d)) meet the security requirements of FIPS 140-2, and how to operate the 1721 and 1760 routers in a secure FIPS 140-2 mode.

Where is the WIC slot on a Cisco 1721 router?

All Cisco 1700 series routers include an auxiliary port supporting 115Kbps Dial-On-Demand Routing, ideal for back-up WAN connectivity. A WIC is inserted into one of the WIC slots, which are located on the back panel of the 1721 and the front panel of the 1760.

Which is Cisco router meets FIPS 140 Level 2?

The Cisco 1721 and 1760 provide a scalable, secure, manageable remote access server that meets FIPS 140-2 Level 2 requirements. This section describes the general features and functionality provided by the Cisco 1721 and 1760 routers. The 1721 and 1760 routers are multi-chip standalone cryptographic modules.

Where is the RISC processor on the Cisco 1700?

Cisco 1700`s RISC-based processor provides the power needed for the dynamic requirements of the remote branch office. The interfaces for the router are located on the rear panel of the Cisco 1721 and the front panel of the Cisco 1760 as shown in Figure 3 .